REBEL Clear Gls Vnl RemAdh 4ml RB599R

RB599R is a 4-mil soft; clear gloss, polymeric stabilized PVC film designed for solvent-based ink jet printing and screen printing. The product is coated on one side with a clear removable, acrylic pressure sensitive adhesive and supplied with a 90# SuperFlat™, C2S polycoated liner that provides excellent lay flat. RB599R is designed medium to long-term outdoor advertising and promotion on flat or slightly curved surfaces. Suggested uses include digitally produced or screen-printed labels, decals, markings, point-of-purchase displays and signs for indoor and

outdoor use.

TYPICAL VALUES*

PHYSICAL PROPERTIES: TEST METHOD

Quick Tack, lb. /in.2 (N/25mm) MACtac CTM-25

Stainless Steel 1.5 (6.5)

Peel Adhesion, lb./in. (N/25 mm) PSTC-1

Stainless Steel - 30 min. 1.7 (7.5)

- 24 hr. 2.2 (9.6)

Thickness, inches (μm)

Face plus adhesive .0042 (106)

Temperature Ranges

Application: 40° to 150°F (-40° to 65°C)

End Use: -40° to 200°F (5° to 94°C)

Dimensional Stability (Shrinkage), inches (mm) MACtac CTM-21

48 hours @ 158°F (70°C) bonded to aluminum (Method D)

MD 0.06 (1.5)

CD 0.04 (1.02)

INTENDED FOR:

Wide format, eco-solvent, solvent-based and UV-cured inkjet printing To achieve the best possible print quality, please make sure that the correct ICC profiles or printer settings are used. Profiles can be obtained from our Distributors or can be downloaded from www.mactac.com . Printer and heater settings and ICC profiles can also be downloaded from some O.E.M. or software manufacturer’s websites.

DURABILITY:

The outdoor durability of the unprinted film is 5 years. RB599R has up to 2 year removability from most surfaces after application. Adhesion to high energy surfaces such as glass, acrylic glass and aluminum may result in some adhesive being left behind. This can be easily cleaned off with Isopropyl alcohol.

IMPORTANT NOTICE: The information given and the recommendations made herein are based on our research and are believed to be accurate, but no

guarantee of their accuracy or completeness is made. In every case, user shall determine before using any product in full scale production, or in any way,whether such product is suitable for user’s intended use for their particular purpose under their own operating conditions. User assumes all risk and liability whatsoever in connection with their use of any product. The products discussed herein are sold without any warranty as to merchantability or fitness for a particular purpose, or any other warranty, express or implied. No representative of ours has any authority to waive or change the foregoing provisions, and no statement or recommendation not contained herein shall have any force of effect unless in an agreement signed by the officers of seller and manufacturer. Nothing contained herein shall be construed to imply the nonexistence of any relevant patents or to constitute a permission, inducement or recommendation to practice any invention covered by any patent without authority from the owner of the patent. The following is made in lieu of all warranties, express or implied: Seller’s and manufacturer’s only obligation shall be to replace or credit such quantity of the product proved to be defective at its discretion.

TM Trademark of Morgan Adhesives Company.

® Registered Trademark of Morgan Adhesives Company.

www.MACtac.com

This use-life estimate is based upon accelerated age studies. Please note that exposure to severe emperatures, ultra-violet light and also in tropical, sub-tropical or desert regions will cause more rapid deterioration. This also applies to polluted areas, high altitude and south facing exposure.

RECOMMENDATIONS:

Always test your combination of REBEL products, inks and laminating films prior to commercial use.

1) Printing Conditions: Print in conditioned pressroom at ±73°F (23°C) and 50% RH. The maximum allowable ink saturation is 270%.

2) Drying Requirements: Solvent, Eco-solvent and Mild-solvent inkjet prints require 24 - 48 hr. drying time - open to the air. Inks do not dry when printed media is rolled up. The prints must be dry prior to lamination.

3) Laminating Conditions: If the printed graphic is likely to be exposed to corrosive liquids, smoke, fumes, and highly polluted areas or there is a likelihood of scratching, it is highly recommended to laminate with Permacolor IP7000 Series or LF3600 High performance overlaminating films.

4) Application: Do not use wet application fluids when applying this media unless it is specifically designed for emulsion adhesives. Standard application fluids including soap or detergent in water may cause the adhesive to turn white.

5) Transportation Conditions: To allow for easy transportation, IMAGin JT5000 series can be rolled up, with the image out, with a minimum diameter of 6 inches (15cm). When the image is not protected by an overlaminate, make sure the print is completely dry and protected in a plastic bag. During transportation or storage, avoid exposing them to extreme temperature and humidity changes.

1) The user is responsible for determining the product’s suitability, including adhesion and if needed,

removal characteristics when used in applications other than listed specifically in this Performance

Guide.

2) If there are any questions about applications, please contact your MACtac sales representative to

discuss your requirements for recommendations.

3) If this is a printed Performance Guide it is an uncontrolled document. Please check the MACtac

website for the latest, most up-to-date version.

SHELF LIFE:

Two years when stored at 75°F (24°C) and 50% relative humidity or less.

* Values given are typical and are not necessarily for use in specification.

CALL 1-888-477-8465  for additional product information