Mactac BFD 2.7 Vehicle Vinyl

PERFORMANCE GUIDE

www.MACtac.com Version #4 (0210)

Approved by J. S.

PRODUCT: IMAGin®

JT5929BFDMQ

PRODUCT DESCRIPTION: JT5929BFDMQ is a 2.7-mil gloss white, polymeric stabilized, soft calendered

PVC film designed for solvent based, ink jet printing. The product is coated on one side with a quick building,

permanent, opaque, acrylic pressure sensitive adhesive with air egress technology and supplied with an 80#

polycoated liner. JT5929BFDMQ is designed for long-term outdoor advertising and promotion applications on

flat or simple curved surfaces. Use of the correct overlaminate will extend the life of the graphic.

TYPICAL VALUES*

PHYSICAL PROPERTIES: TEST METHOD

Peel Adhesion, lb. /in. (N/25mm) FTM - 1

180° on Glass - 15min 1.8 (8)

- 30 min. 3.0 (13)

- 24 hr. 3.9 (17)

Quick Tack on SS, lb. /in² (N/25mm) 5.0 (22) FTM - 9

Dimensional Stability, (%) FTM - 14

48 hours @ 158°F max 0.5 10” x 10” Sample

bonded to aluminum.

Temperature Ranges,

Minimum Application: 50°F (+10°C)

End Use: -58° to 194°F (-50° to 90°C)

Flammability Self-extinguishing ISO 3795

Salt Water Spray ASTM B 117-03

100 hours @ 5% solution no change

Water Immersion

100 hours immersed @ RT no change

INTENDED FOR: Wide format, eco-solvent, solvent-based, latex and UV-cured inkjet printing To achieve the

best possible print quality, please make sure that the correct ICC profiles or printer settings are used. Profiles can be

obtained from our Distributors or can be downloaded from www.mactac.com/graphics . Printer and heater settings

and ICC profiles can also be downloaded from some O.E.M. or software manufacturer’s websites.

The ICC profiles are provided solely as a customer resource. Print environments, the individual nature of printing

systems, inks and software can significantly affect output. It is the customer’s responsibility to determine the

suitability of any profile for use in their specific print environment.

1) The user is responsible for determining the product’s suitability, including adhesion and if needed, removal characteristics when used in applications other than listed specifically in this Performance Guide.

2) If there are any questions about applications, please contact your MACtac sales representative to discuss your requirements for recommendations.

3) If this is a printed Performance Guide it is an uncontrolled document. Please check the MACtac website for the latest, most up-to-date version.

DURABILITY: The outdoor durability of the unprinted film is 7 years. Overlamination of the inkjet-printed

material with Permacolor® overlaminates delays color fading that may occur over time. This color fading is mainly

IMPORTANT NOTICE: The information given and the recommendations made herein are based on our research and are believed to be accurate, but no guarantee of their accuracy or completeness is made. In every case, user shall determine before using any product in full scale production, or in any way, whether such product is suitable for user’s intended use for their particular purpose under their own operating conditions. User assumes all risk and liability whatsoever in connection with their use of any product. The products discussed herein are sold without any warranty as to merchantability or fitness for a particular purpose, or any other warranty, express or implied. No representative of ours has any authority to waive or change the foregoing provisions, and no statement or recommendation not contained herein shall have any force of effect unless in an agreement signed by the officers of seller and manufacturer. Nothing contained herein shall be construed to imply the nonexistence of any relevant patents or to constitute a permission, inducement or recommendation to practice any invention covered by any patent without authority from the owner of the patent. The following is made in lieu of all warranties, express or implied: Seller’s and manufacturer’s only obligation shall be to replace or credit such quantity of the product proved to be defective at its discretion.

TM Trademark of Morgan Adhesives Company.

® Registered Trademark of Morgan Adhesives Company.

www.MACtac.com

dependent upon the inks quality (see technical data sheets given by the ink manufacturers) and pressure sensitive

media being used. MACtac requires the registration of a completed and signed Inspection Report for each vehicle wrap in the unlikely event of a future claim. This report identifies any potential problem areas and clearly defines the obligations between the applicator and the vehicle owner. A completed copy of the inspection report and the appropriate vehicle template must be on file at MACtac prior to application. The inspection report is attached at the end of the Application Guide TA2501 and the B-Free Vehicle Warranty MAC2588 which are available on the MACtac website at www.mactac.com/graphics . Registration acknowledges that your company has received the Application Guide and a copy of this warranty and agrees to all the requirements and limitations outlined in these documents.

REMOVABILITY: JT5929BFDMQ, when laminated, is cleanly removable for up to five years after application

with high heat. “Removability” means that when removing the emblem, the pressure sensitive film will leave less

than 20% of the adhesive on the substrate. Some substrates are affected by the application of the JT5929BFDMQ

such as; acrylic glass, polycarbonate, polystyrene, nitro-cellulose paints and plasticized PVC’s. Besides damaging

the substrate, subsequent removal could be difficult.

RECOMMENDATIONS: Always test your combination of JT5000 products, inks and laminating films prior to

commercial use.

1. Printing Conditions: Print in conditioned pressroom at ±73°F (23°C) and 50% RH. The maximum allowable

ink saturation is 270%.

2. Drying Step: It is critical the JT5929BFDMQ print is properly dried prior to laminating or application. While

this is important in all solvent inkjet prints it’s especially so with JT5929BFDMQ. We strongly recommend

leaving the print open to the air (not rolled up in a tube) for a minimum of 24 hours prior to lamination or

application. Residual solvents in the vinyl and adhesive will negatively affect the bubble free properties of the

adhesive and can result in a significant build or loss in adhesion resulting in potential substrate or graphic

failure and/or more residual adhesive being left behind upon removal. Additional hot air drying or IR drying

will speed up the drying process and shorten the overall drying time.

3. Laminating Conditions: Ensure print is perfectly dry. Material must have 24 - 48 hr. drying time open to the

air, not rolled up in a tube, prior to lamination or transportation. If the printed graphic is likely to be exposed to

corrosive liquids, smoke, fumes, and highly polluted areas or there is a likelihood of scratching, it is highly

recommended to laminate with Permacolor LF3600 series (High Performance) overlaminating films. Please

be aware that adding an overlaminate will significantly reduce conformability to complex surfaces.

4. Not recommended surfaces includes, but is not limited to; rubber and plastic, aged paint (chalking) and

metals (corrosion or oxidation), improperly cured paint, surfaces with poor paint-to-surface adhesion, over

existing graphics that must remain upon removal, oily surfaces, unpainted wood, etc.

5. Transportation Conditions: To allow for easy transportation, IMAGin JT5000 series can be rolled up, with

the image out, with a minimum diameter of 6 inches (15cm). When the image is not protected by an

overlaminate, make sure the print is completely dry and protected in a plastic bag. During transportation or

storage, avoid exposing them to extreme temperature and humidity changes.

6. Removing JT5929BFDMQ: Heat the vinyl to approx. 160° - 180°F using a heat gun or propane torch (be

careful not to burn the vinyl or the substrate). Pull off the BFDQ in small pieces. Listen to the sound of the

vinyl as it’s pulled off. The noise level will increase as the vinyl and adhesive cools. At a certain level

(experience is the best teacher) you will know when it is time to re-heat. This will help you prevent paint

failure as you pull the graphic off. Any adhesive residue can be removed using a towel soaked in alcohol or

other commercially available adhesive remover. Be sure to follow manufacturer’s directions and use personal

protective gear.

SHELF LIFE:

2 year from D.O.M. when stored at 60/77°F (15/25°C) and 50% relative humidity in the original package.

* Values given are typical and are not necessarily for use in specification.

IMPORTANT NOTICE: The information given and the recommendations made herein are based on our research and are believed to be accurate, but no guarantee of their accuracy or completeness is made. In every case, user shall determine before using any product in full scale production, or in any way, whether such product is suitable for user’s intended use for their particular purpose under their own operating conditions. User assumes all risk and liability

whatsoever in connection with their use of any product. The products discussed herein are sold without any warranty as to merchantability or fitness for a particular purpose, or any other warranty, express or implied. No representative of ours has any authority to waive or change the foregoing provisions, and no statement or recommendation not contained herein shall have any force of effect unless in an agreement signed by the officers of seller and

manufacturer. Nothing contained herein shall be construed to imply the nonexistence of any relevant patents or to constitute a permission, inducement or recommendation to practice any invention covered by any patent without authority from the owner of the patent. The following is made in lieu of all warranties, express or implied: Seller’s and manufacturer’s only obligation shall be to replace or credit such quantity of the product proved to be defective

at its discretion.

TM Trademark of Morgan Adhesives Company.

® Registered Trademark of Morgan Adhesives Company.