PRODUCT DESCRIPTION:
JT5529BFD Pro is a 2.1-mil soft white gloss, highly conformable, laminated PVC film designed for solvent-based ink jet printing. The product is coated on one side with an aggressive, permanent, opaque, acrylic pressure sensitive adhesive with air egress technology and supplied with an 80# polycoated 2-side release liner. JT5529BFD Pro designed for use by experienced applicators for long-term outdoor, vehicle markings on flat, curved, complex and riveted surfaces. Use of the correct overlaminate will extend the life of the graphic.You Must be Logged in to Add the Item to your Cart.
Description
PERFORMANCE GUIDE
www.MACtac.com Version #6 (0410)
Approved by J. S.
PRODUCT: IMAGin®
JT5529BFD Pro
PRODUCT DESCRIPTION: JT5529BFD Pro is a 2.1-mil soft white gloss, highly conformable,
laminated PVC film designed for solvent-based ink jet printing. The product is coated on one side with
an aggressive, permanent, opaque, acrylic pressure sensitive adhesive with air egress technology and
supplied with an 80# polycoated 2-side release liner. JT5529BFD Pro designed for use by experienced
applicators for long-term outdoor, vehicle markings on flat, curved, complex and riveted surfaces. Use
of the correct overlaminate will extend the life of the graphic. Graphics manufactured using IMAGin
B-Free vinyl and PSA over-laminating film when applied over rivets may result in some tenting and
lifting around the rivet and does not constitute a breach in warranty.
TYPICAL VALUE*
PHYSICAL PROPERTIES: TEST METHOD
Peel Adhesion, lb. /in. (N/25mm) FTM - 1
180° on glass - 15min 2.3 (10.0)
- 30 min. 2.5 (10.5)
- 24 hr. 2.7±0.7 (12±3)
Quick Tack on Glass, lb. /in² (N/25mm) 4.1±0. 7 (18±3) FTM - 9
Dimensional Stability, (%) FTM - 14
48 hours @ 158°F max 0.5 10” x 10” Sample
bonded to aluminum.
Temperature Ranges,
Minimum Application: 50°F (+10°C)
End Use: -58° to 194°F (-50° to 90°C)
Flammability Self-extinguishing ISO 3795
Salt Water Spray ASTM B 117-03
100 hours @ 5% solution no change
Water Immersion
100 hours immersed @ RT no change
INTENDED FOR: Wide format, eco-solvent, solvent-based, latex and UV-cured inkjet printing. To
achieve the best possible print quality, please make sure that the correct ICC profiles or printer settings
are used. Profiles can be obtained from our Distributors or can be downloaded from
www.mactac.com/graphics . Printer and heater settings and ICC profiles can also be downloaded from
some O.E.M. or software manufacturer’s websites. JT5529BFD can also be screen printed.
The ICC profiles are provided solely as a customer resource. Print environments, the individual nature of
printing systems, inks and software can significantly affect output. It is the customer’s responsibility to
determine the suitability of any profile for use in their specific print environment.
NOT INTENDED FOR: Cut lettering applications. Use non-air--egress products for these applications.
1) The user is responsible for determining the product’s suitability, including adhesion and if
needed, removal characteristics when used in applications other than listed specifically in
this Performance Guide.
2) If there are any questions about applications, please contact your MACtac sales
representative to discuss your requirements for recommendations.
3) If this is a printed Performance Guide it is an uncontrolled document. Please check the
MACtac website for the latest, most up-to-date version.
DURABILITY: The outdoor durability of the unprinted film is 10 years. Over lamination of the inkjetprinted
material with Permacolor® overlaminates delays eventual color fading that may occur over time.
This color fading is mainly dependent upon the quality of the inks (see technical data sheets given by the
ink manufacturers), the pressure sensitive media being used and the region in which the graphics are to be
displayed. MACtac requires the registration of a completed and signed Inspection Report for each vehicle wrap in
the unlikely event of a future claim. This report identifies any potential problem areas and clearly defines
the obligations between the applicator and the vehicle owner. A completed copy of the inspection report
and the appropriate vehicle template must be on file at MACtac prior to application. The inspection
report is attached at the end of the Application Guide TA2501 and the B-Free Vehicle Warranty
MAC2588 which are available on the MACtac website at www.mactac.com/graphics . Registration
acknowledges that your company has received the Application Guide and a copy of this warranty and
agrees to all the requirements and limitations outlined in these documents.
REMOVABILITY: JT5529BFD Pro, when laminated, is cleanly removable for up to five years after
application with high heat. “Removability” means that when removing the emblem, the pressure sensitive
film will leave less than 20% of the adhesive on the substrate. Some substrates are affected by the
application of the JT5529BFD Pro such as; acrylic glass, polycarbonate, polystyrene, nitro-cellulose
paints and plasticized PVC’s. Besides damaging the substrate, subsequent removal could be difficult.
RECOMMENDATIONS:
Always test your combination of JT5000 products, inks and laminating films prior to commercial use.
1. Printing Conditions: Print in conditioned pressroom at ±73°F (23°C) and 50% RH. The maximum
allowable ink saturation is 270%.
2. Drying Step: It is critical the JT5529BFD print is properly dried prior to laminating or application.
While this is important in all solvent inkjet prints it’s especially so with JT5529BFD. We strongly
recommend leaving the print open to the air (not rolled up in a tube) for a minimum of 24 hours prior
to lamination or application. For average ink saturation (i.e.: 270%). Higher levels of ink will require
additional drying time up to 48 hours or more. Residual solvents in the vinyl and adhesive will
negatively affect the bubble free properties of the adhesive and can result in a significant build or loss
in adhesion resulting in potential substrate or graphic failure and/or more residual adhesive being left
behind upon removal. Additional hot air drying or IR drying will speed up the drying process and
shorten the overall drying time.
3. Laminating Conditions: Ensure print is perfectly dry. Material must have 24 - 48 hr. drying time
open to the air, not rolled up in a tube, prior to lamination or transportation. If the printed graphic is
likely to be exposed to corrosive liquids, smoke, fumes, and highly polluted areas or there is a
likelihood of scratching, it is highly recommended to laminate with Permacolor LF3640 series
(RAYZor) overlaminating films. Please be aware that adding an overlaminate will significantly
reduce conformability to complex surfaces.
4. Application Tape: Use of an application tape (transfer tape) is not recommended or needed if an
overlaminate is used. If you must use an application tape, use one with a Steel adhesion no greater
than 4 - 6 oz/in. Upon removal of the application tape, you must head and re-squeegee all edges.
Failure to do this will result in edge lifting.
5. Not recommended surfaces includes, but is not limited to; rubber and plastic, aged paint (chalking)
and metals (corrosion or oxidation), improperly cured paint, surfaces with poor paint-to-surface
adhesion, over existing graphics that must remain upon removal, oily surfaces, unpainted wood, etc.
TM Trademark of Morgan Adhesives Company.
® Registered Trademark of Morgan Adhesives Company.
www.MACtac.com
IMPORTANT NOTICE: The information given and the recommendations made herein are based on our research and are believed to be accurate, but no guarantee of their accuracy or completeness is made. In every case, user shall determine before using any product in full scale production, or in any way, whether such product is suitable for user’s intended use for their particular purpose under their own operating conditions. User assumes all risk and liability whatsoever in connection with their use of any product. The products discussed herein are sold without any warranty as to merchantability or fitness for a particular purpose, or any other warranty, express or implied. No representative of ours has any authority to waive or change the foregoing provisions, and no statement or recommendation not contained herein shall have any force of effect unless in an agreement signed by the officers of seller and manufacturer. Nothing contained herein shall be construed to imply the nonexistence of any relevant patents or to constitute a permission, inducement or recommendation to practice any invention covered by any patent without authority from the owner of the patent. The following is made in lieu of all warranties, express or implied: Seller’s and manufacturer’s only obligation shall be to replace or credit such quantity of the product proved to be defective at its discretion.
6. Transportation Conditions: To allow for easy transportation, IMAGin JT5000 series can be rolled
up, with the image out, with a minimum diameter of 6 inches (15cm). When the image is not
protected by an overlaminate, make sure the print is completely dry and protected in a plastic bag.
During transportation or storage, avoid exposing them to extreme temperature and humidity changes.
7. Removing JT5529BFD Pro: Heat the vinyl to approx. 160° - 180°F using a heat gun or propane
torch or a weed burner for large areas (be careful not to burn the vinyl or the substrate). Pull off the
BFD in small pieces. Listen to the sound of the vinyl as it’s pulled off. The noise level will increase
as the vinyl and adhesive cools. At a certain level (experience is the best teacher) you will know
when it is time to re-heat. This will help you prevent paint failure as you pull the graphic off. Any
adhesive residue can be removed using a towel soaked in alcohol or other commercially available
adhesive remover. Be sure to follow manufacturer’s directions and use personal protective gear.
SHELF LIFE:
2 years from D.O.M. when stored at 60/77°F (15/25°C) and 50% relative humidity in the original
package.
* Values given are typical and are not necessarily for use in specification.